How To Jump A Car When You Can't Reach The Negative

Connect the other black negative cable to a clean unpainted metal surface under the disabled cars hood. The vehicles shouldnt touch one another.

Pin On Inspirational Quotes

START THE DONOR CAR so that the battery can supply power to the dead battery.

How to jump a car when you can't reach the negative. Connect one end of the black negative jumper cable to the black - negative post of the fully charged car battery. How to jump-start a car steps. Walk over to the car with the dead battery.

Use one of the metal struts that holds the hood open. Connect the other end of the black negative jumper cable to a metal part of the dead car that is unpainted as far from the battery as the cable will reach. This is so you can avoid sparks from occurring near the battery where flammable hydrogen gas may be present resulting in a possible explosion.

Once the cables are removed drive the newly live car directly to AutoZone for a new battery or to a mechanic for service. Carefully remove the negative cable and then the positive cable from both cars or just the one if youre using a jump starter. Typically when a person jumpstarts a car sparks can occur.

Attach the last black clip to an unpainted metal surface on your car that isnt near the battery. This will help ensure a safe jump. Thats why it is recommended that you connect the negative jumper cable to the vehicle body and not the negative post of the battery.

Do not attach this clamp to the negative terminal on the dead cars battery. Attach the other red clip to the positive terminal of the other car. Park the car that needs to be jump-started next to a car with a good battery.

Connect the other red clamp to the positive terminal of the good battery. Connect one black clamp to the negative - terminal of the good battery. Well we decided to demonstrate yo.

Do not connect the black negative cable clamp to the dead battery. Have you ever wondered what happens if you switch the Positive and Negative Battery terminal when you jump start your car. Mar 12 2016 at 900 AM When jumping a car it is advised to use a ground such as a bolt or bracket for the black negative cable instead of connecting it to the negative terminal on the dead.

Pull the car close enough so that the cables will easily reach from the battery of one car to the battery of the other. Make sure the other end doesnt touch any part of the cars engine or body or you could get a dangerous spark. Connect the NEGATIVE clamp on the ground terminal of your Mercedes-Benz or any part of the engine or frame that is not painted.

Attach one black jumper cable clamp to the negative terminal of the working live cars battery. Attach one of the black clips to the negative terminal on the other battery. I tried to use our 2nd vehicle a 2010 Ford Escape as the assisting car to jump start mine.

One of the metal struts that hold the hood open is a good place to clip the second black or negative clip. This will ground the circuit and help prevent sparking. Clamp the positive red or yellow cable to the positive terminal of the weak battery.

On the vehicle with the dead battery also identify an unpainted metal surface that isnt next to the battery. If the vehicle doesnt start immediately you may want to try two more times. Now attach the red clamp at the other end of the jumper cable the end youve laid on the ground to the good batterys.

Connect the other black clamp to a piece of grounded metal on the dead car preferably the bolt where the thick negative cable from the battery connects to the chassis. But when I looked at the engine compartment of the Escape I found that the battery is positioned in such a way that the negative terminal is completely inaccessible and there is no physical method that I can find to connect jumper leads to that battery. Instead attach that clamp to an unpainted metal part of the car such as a shiny clean nut on the engine block.

Next connect a black clamp to the negative terminal of the live battery. IDLE the donor car allowing it to run for a few minutes. Park the car youll use for jump-starting next to the one with the dead battery positioned close enough so that the cables will reach.

Attach the other end of that cable the second black jumper cable clamp to an unpainted piece of stationary metal on the car with the dead battery. Somewhere on the engine block is a good place. Connect the NEGATIVE clamp on the negative terminal of the helper car.

TEST the interior light of the car being jump started. Clamp the other end of the positive cable to the positive terminal of the good battery. 2 Connect one of the red positive jumper cable clamps to the dead batterys red positive post.

You cant jump-start a car if you cant get the juice to its battery. Instead of connecting the second black to the negative terminal on the dead battery find an unpainted metal surface on the. Connect the other POSITIVE clamp on the other end of the booster cables on the Jump Start Terminal of your Mercedes-Benz.

Unless you want to see flying sparks and a possible explosion do not connect the negative cable to the negative terminal of the dead battery. Park the car with the good battery next to the car with the dead battery.

Using A Car With An Inaccessible Negative Battery Terminal To Jump Start Motor Vehicle Maintenance Repair Stack Exchange